Wusthof 10-Inch Sharpening Steel - on Amazon.com
When that time comes that you need to touch up the sharp edge of your Wusthof knife the 10" steel is a good option. The Wusthof 10" inch steel can realign your knife edge quickly and easily. Honing steels are often confused as sharpeners. Your honing steel will realaign your knife edge but will not put a new edge on it. In trying to explain what a honing steel does try to imaging your sharpening steel and your toothbrush. It is a maintaince tool that you use everyday. In the case of your knife this would be maintaining the knifes edge. Now eventually you would need to see your dentist. That would be a sharpener. This would be a more detailed and agressive action and they would actually remove metal from the edge of the knife. Much like a dentist would do to your teeth. Now to maintain healthy teeth you brush everyday. To maintain a sharp knife you should steel your knife everyday. And remember only go to the Dentist(sharpener) once or twice a year.
Reviews of Wusthof 10 Inch Sharpening Steel
Not all steels are the same!
Rating by : Warren J. Dew, 
A lot of people assume that all sharpening steels are the same. That is not true.
I've owned this sharpening steel for about 6 years. It replaced a steel I had been using for about 20 years. I usually hone my knives between every use. With my previous steel, it typically took 4-10 swipes to restore a razor edge, with occasional resharpening using an alumina (corundum) stone; with this steel, I can get the same razor edge in 1-2 swipes, and never need to use the stone.
This is consistent with some hardness measurements I've seen on the web, which indicated that Wusthof sharpening steels were significantly harder than those from other major manufacturers, including their closest competitor, Henckels.
There is one downside to this steel: the steel itself only extends about half an inch into the plastic handle. If you just plop it into its slot in the knife block after each use, the steel will eventually fall out of the handle. It's not terribly difficult to force the steel back into the handle, though, and I can put up with having to do that every few years in exchange for the pleasure of using this steel on my knives.
My Knives Are Calling To Me to Cut Something!!
Rating by : Mike Lip "Full-time Consumer", 
Wow - I read an article in Family Handyman about sharpening your own knives. They recommended starting out with the Wüsthof 2-Stage Knife Sharpener, then finishing with a sharpening steel.
So... We've had knives that I've tried to sharpen before but didn't know how. Was a pain in the butt. So we kept getting new knives. Now we have a drawer full of them.
I bought this steel and the 2-stage sharpener, pulled a dull knife out of the drawer, and about 5 minutes later the thing was SHARP! So I kept going, and now we have a drawer full of super sharp knives that are a PLEASURE to use.
The secret here is to use the carbide part of the 2-stage sharpener for really dull knives. Run it through enough times 'till it "catches" on your fingernail when you slide it down (perpendicular, not parallel...). Then go to the ceramic part and slide the knife 10 or so times. Both are set up so the knife is held at the correct angle.
Finally, pull out your steel, place it TIP DOWN on a cutting board. Position your knife so it's at about a 25 degree angle to the steel. Easy to do if you start at 90 degrees, then cut that in half to 45, then cut in half again. Then firmly but gently run the blade down the steel, pulling it toward you as you slide it downward.
Do that a few times on each side, and you're guaranteed a sharp edge.
The way to keep it sharp is to run it down the steel a few times each time YOU FINISH USING IT. Cutting with the knife will cause very fine deviations in the edge of the blade. Running it on the steel straightens the edge back up.
i love things that make my life easier. This does so, and at a good price. And... I threw away two other sharpening steels after using the Wüsthof. A previous reviewer mentioned how quickly it works, and he's right!
This steel changed my life.
Rating by : Joshua G. Feldman "Technophile",
Initially I didn't understand the steel - and what honing was. Even after I figured it out I didn't see the point until I ran into this incredible steel. Unlike the cheap little ones included with sets, this steel has a big enough diameter, long enough length, and incredible machining on the grooves to really effectively hone every time out. It also has an awesome molded handle and big chunky hanging ring (which you might need because a 12" steel will stick out of most blocks).
Why use a steel to hone? Stainless steel is ductile and the edge of a knife is a place where the steel is very very thin. In use the very edge will bend or fold over microscopically. Then, then next cut you make will be on what will be on the fold - rather than on the sharp edge. These micro folds can be straightened out by the use of a Steel - a process called "honing". Honing involves wiping the blade across a hard steel rod which has a large number of tiny parallel grooves cut in it. When the wiping motion is done like carving - at the angle the edge is ground - the steel literally unfolds the edge and gives the fine edge a micro ripple. In this way, steeling a sharp knife that has recently gone dull is like magic - full sharpness is immediately restored. Over time, however, all this cutting and steeling will actually wear metal away from the edge, or some folds will become permanent and the edge itself will become dull and the knife will need to be sharpened.
"Steeling", or "honing" is emphatically NOT "sharpening". These are two fundamentally different knife care techniques. In short, the steel restores the edge as much as it can, without removing metal; and the sharpening actually removes metal to grind a new edge. Sharpening is done on an abrasive stone or a metal plate onto which diamond or other abrasive has been adhered. Sharpening actually removes metal - so it actually reduces the life of the knife to a certain extent.
The big message here is to steel frequently (ideally every single time you use the knife - right before you use it) and to sharpen infrequently (no more than once or twice a year). Chefs are always depicted holding the steel in the air pointing up and flicking the knife rapidly over it. In practice it is almost impossible to properly steel a knife this way. Hold the steel facing down with the tip pressed into your cutting board and cut down, pulling the knife towards you with a slicing motion, with your knife at the grind angle (10-15 degrees for Asian style and 20-25 degrees for Western) while the steel is stabilized rock solid. This way the steel is held rigidly vertical and the angle is easy to see. When you get the angle right you can feel the edge "bite" a little into the steel.
Since you should be using the steel frequently, I highly recommend you get the best steel you can. There are some very real differences in the machining of the grooves. You should also be aware that "diamond" or "sharpening" steels are for sharpening, NOT honing. The other big factor in choosing a steel is length. Get a big long one. Theoretically your steel should be 1-2" longer than your longest knife - so a 9" steel ought to be fine if you have an 8" knife. In practice, the longer the steel, the more comfortable and easy it is to steel. I've tried honing an 8" knife with a 9" steel and you have to do two passes to get one stroke. Henkel's 12" steel is a best seller and a great value: J.A. Henckels Twin Pro S 12-Inch Honing Steel. I, personally, went with Wusthof's, which is much more expensive but is utterly exquisite and a dynamite pleasure to use: Wusthof 12 in. Sharpening Steel. Be aware that these big long 12" steels will stick out of most knife blocks. The excellent functionality is well worth the little bit of trouble of it sticking out a bit.
FYI - the item reviewed is Wusthof's 4474 - the 12" steel with modern square handle. 4474 is the item being sold here - the photograph was correct until late May 2008, when the photograph of 4471 (a 12" Wusthof steel with an old fashioned beehive handle) was substituted. The 4471 is also excellent - with a virtually identical steel. However I find the handle of 4474 more comfortable. Be aware that the photograph is not of the item on sale. To see 4474 link to [...]
10-Inch sharpening steel; Magnetic steel that attracts metal fibers; Slip-resistant plastic handle fits comfortably in the hand; Loop on the handle for hanging
This tool serves a vital role in the kitchen by realigning, or resetting, a knifes' edges, which bend this way and that when contacting a cutting surface. (Often ...
From Wusthof comes this 10-in. Sharpening Steel - part of their Ikon Blackwood line. Wusthof Ikon Blackwood10-in. Sharpening SteelFull tang triple riveted rare ...
Find great deals on eBay for wusthof sharpening steel and wusthof sharpener. Shop with confidence.
ShopWiki has 23 results for Wusthof 10 Inch Sharpening Steel, including Wusthof Ikon Blackwood Sharpening Steel - Frontgate, Wusthof 10-in. Sharpening Steel with Loop ...
No comments:
Post a Comment